Just How To Replace A Bathtub (For Newbies).
Just How To Replace A Bathtub (For Newbies).
Blog Article
Presented here down the page you'll find a bunch of awesome advice related to A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a new one is also a moderately hard job. If the old bathtub is readily obtainable, the job can relocate quickly; if you need to open a wall surface to remove the old bathtub and place the brand-new tub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the new one. Make sure you have certified on your own for the job and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed task, it is better to think about using one before you begin. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have already acquired a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools as well as material list should make up the following:
Preparing for the Installment
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the limited accessibility that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Fill the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait up until the tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in location between the faucet as well as the sink. Safeguard the faucet in position with the producer supplied backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub, I was thinking sharing that piece of writing was a great idea. If you liked our page kindly don't forget to share it. Thanks a lot for your time invested reading it.
Go Deal Report this page